# Internet sharing
Internet sharing between a PC and the BeagleBone boards can be done on any OS. Thus, the next sections will indicate the different instructions for enabling internet sharing.


# Windows PC

The following guide is based on [^1]. In the `cmd` application, run the next command to determine the connection *IP* between your PC and the BBB:

```
ping 192.168.7.2

Pinging 192.168.7.2 with 32 bytes of data:
Reply from 192.168.7.2: bytes=32 time=1ms TTL=64
Reply from 192.168.7.2: bytes=32 time=2ms TTL=64
Reply from 192.168.7.2: bytes=32 time=1ms TTL=64
Reply from 192.168.7.2: bytes=32 time=2ms TTL=64

Ping statistics for 192.168.7.2:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 1ms, Maximum = 2ms, Average = 1ms
	
```

if you get 0% loss, then the BBB has a network connection between PC and BBB:

	BBB        <---->    Windows PC
192.168.7.2           192.168.7.1 

Next, open the **network connection** application to identify the internet connection adapter and the BBB-USB connection:

![Network Connection](./nc.png)

In my case, the `Ethernet` connection is the one with the Internet, while the `Ethernet 3` is the BeagleBone; notice that the BB indicates a **USB Host Device**.

![Networks](./connections.png)

Then, the network with an internet connection must be shared with the BBB. Therefore, make right-click on the *Ethernet connection* with the internet and select options:

![options](./properties.png)

then click on the `Sharing` tab and enable the `Internet Connection Sharing` as shown below. Now, you have to select one network connection to share the internet; remember that, in my case, it is `Ethernet 3` (USB-BBB Device). 


![share option](./share.png)

After that, we should open the USB-Device network connection properties by right-clicking on its icon:

![](./tcp.png)

then select the `Internet Protocol Version 4(TCP/IPv4)` and click on the properties button; at this point, you will probably lose the connection between the BBB and Windows. Also, the OS will make some undesirable changes in the assigned IP to the PC; it is wrong (it must be 192.168.7.1)

![](./wrong-ip.png)

next, we have to solve this error assignment by clicking on the `Obtain an IP address automatically` option or writing the correct IP by yourself

![](./ipok.png)

Finally, we have to indicate to the BBB the IP used for any outside requests using the next commands in the **BBB's Shell**:

```
sudo /sbin/route add default gw 192.168.7.1
```

and then check with `ping 8.8.8.8` command.


```
echo "nameserver 8.8.8.8" >> /etc/resolv.conf
```

# GNU/Linux

In the PocketBeagle, console type the following
```
ifconfig usb0 192.168.7.2
route add default gw 192.168.7.1
```

In the linux console of host system type

```
$ sudo su
#wlan0 is my internet facing interface, eth5 is the PocketBeagle USB connection
$ ifconfig eth5 192.168.7.1
$ iptables --table nat --append POSTROUTING --out-interface wlan0 -j MASQUERADE
$ iptables --append FORWARD --in-interface eth5 -j ACCEPT
$ echo 1 > /proc/sys/net/ipv4/ip_forward
```

Incase network not accessible then type the following in BBB terminal

```
echo "nameserver 8.8.8.8" >> /etc/resolv.conf

```


# References 
[^1]: https://ofitselfso.com/BeagleNotes/HowToConnectBeagleboneBlackToTheInternetViaUSB.php

[^2]: http://jpdelacroix.com/tutorials/sharing-internet-beaglebone-black.html

[^3]: https://www.dangtrinh.com/2015/05/sharing-internet-with-beaglebone-black.html 

[^4]: https://www.elementzonline.com/blog/Sharing-Internet-using-Network-Over-USB-in-PocketBeagle