\documentclass{beamer}
\usepackage[spanish]{babel}
\usepackage[utf8]{inputenc}
\usepackage{ragged2e}
\usetheme{Warsaw}
\usecolortheme{crane}
\useoutertheme{shadow}
\useinnertheme{rectangles}

\title[Introduction to CircuitPro]{Milling Circuit Boards with CircuitPro and S63 LPKF Machine}
\institute[ITM]{Instituto Tecnológico de Morelia\\
Maestría en Ciencias en Ingeniería Electrónica\\
''José María Morelos y Pavón"}

\begin{document}
		
\frame{\titlepage}

\begin{frame}
\frametitle{Índice}
\tableofcontents
\end{frame}



\section{Machine Setup}
\begin{frame}
\frametitle{Machine Setup}
\begin{figure}[!h]
	\centering
	\includegraphics[width=3in]{selecciondemaquina.JPG}
	\caption{Hardware configuration}
\end{figure}
\end{frame}

\begin{frame}
\begin{figure}[!h]
	\centering
	\includegraphics[width=3in]{herramientas.JPG}
	\caption{Tool selection window}
\end{figure}
\end{frame}

\subsection{The tool magazine}
\begin{frame}{Milling and Drilling Tools}
\begin{figure}[!h]
	\centering
	\includegraphics[width=4.5in]{tools}
\end{figure}
\end{frame}


\begin{frame}{}
\begin{figure}[!h]
	\centering
	\includegraphics[width=2.5in]{drilling}
\end{figure}
\end{frame}


\begin{frame}{}
\begin{figure}[!h]
	\centering
	\includegraphics[width=3in]{herramientasLength}
\end{figure}
\end{frame}

\subsection{CAD systems}
\begin{frame}
\begin{figure}[!h]
	\centering
	\includegraphics[width=3in]{selecciondeprogramas.JPG}
	\caption{CAD Software Selection}
\end{figure}
\end{frame}
%-------------------
\section{The CircuitPRO GUI}
\begin{frame}
\frametitle{GUI}
	\begin{figure}[!h]
		\centering
		\includegraphics[width=4.2in]{interfaz.png}
		\caption{The CircuitPro Graphic User Interface}
	\end{figure}
\end{frame}
%-------------------
\section{How to create a new project}
\subsection{Project stages}

\begin{frame}
	\frametitle{Project stages}
	\begin{block}{}
		\justifying
		  Once the machine has been configured,  most of the PCBs follow the next process:
		\begin{itemize}
			\item Load a template project \textbf{(Single Side, Double Side, ...)} 
			\item Import the \textbf{Gerber} files
			\item Create the tool-paths and link the tools
			\item Board Production
		\end{itemize}
	\end{block}
\end{frame}

\begin{frame}

	\begin{figure}[!h]
		\centering
		\includegraphics[width=4.5in]{crearproyecto.png}
		\caption{Cargar plantilla predeterminada}
	\end{figure}
\end{frame}

\subsection{How many layers}
\begin{frame}
\begin{figure}[!h]
	\centering
	\includegraphics[width=3.5in]{bottonlado.JPG}
	\caption{Selección de tipo de PCB}
\end{figure}
\end{frame}

\subsection{Substrate}
\begin{frame}

\begin{figure}[!h]
	\centering
	\includegraphics[width=3.5in]{material.JPG}
	\caption{Selección de material}
\end{figure}
\end{frame}

\subsection{Layer files}

\begin{frame}

\begin{figure}[!h]
	\centering
	\includegraphics[width=4.5in]{importar.JPG}
	\caption{Layer files importing}
\end{figure}
\end{frame}

\begin{frame}
\frametitle{Allowed files}
\begin{figure}[!h]
	\centering
	\includegraphics[width=2.4in]{archivosadmitidos.png}
	\caption{Archivos admitidos}
\end{figure}
\end{frame}

\begin{frame}
\begin{block}{}
	\justifying
	The file extension depends on the CAD software used. For Altium, the layers generated are the KeepOut, Botton Layer and Top Layer, respectively (\texttt{*.GKO, *.GBL y *.GTL}). 
	
%	Al importar los archivos generados dependiendo del programa utilizado será el formato en que vengan. Las extensiones de los archivos podrían describir qué son, por ejemplo: \texttt{*.GKO, *.GBL y *.GTL} generados por Altium contienen las capas KeepOut, Botton Layer y Top Layer respectivamente.
\end{block}
	
\end{frame}

\begin{frame}
\frametitle{Tipos de archivos admitidos}

\end{frame}

\subsubsection{The Layers}

\begin{frame}
\frametitle{Botton layer}
\begin{figure}[!h]
	\centering
	\includegraphics[width=3.2in]{importarasignarb.png}
	\caption{Botton layer file}
\end{figure}
\end{frame}

\begin{frame}
\begin{figure}[!h]
	\centering
	\includegraphics[width=3.2in]{importarasignart.png}
	\caption{Top layer file}
\end{figure}
\end{frame}


\subsubsection{The Drill Layers}
\begin{frame}
\frametitle{The Drill Layers}
\begin{figure}[!h]
	\centering
	\includegraphics[width=3.2in]{importarasignar.png}
	\caption{Drill layer importing}
\end{figure}
\end{frame}

\subsubsection{Contour router layer}
\begin{frame}
\frametitle{Capas de corte}
\begin{figure}[!h]
	\centering
	\includegraphics[width=3.2in]{importarasignarbordes.png}
	\caption{The board Outline Layer}
\end{figure}
\end{frame}
\end{document}